Can you cut graphite shaft down

To answer these questions, we spoke with prominent golf club designer and builder Tom Wishon, founder of Tom Wishon Golf Technology.

Wishon explained:. From this form, the clubmakers have to cut the shaft, often from both the tip and grip ends, to properly install it into each clubhead. All golf shafts taper; that is, their circumference is greater at the grip end than at the tip end.

That means that the grip end is the strongest part of the shaft and the tip end the weakest, which, Wishon says, leads trimming to have different effects:. But it's impossible to state an across-the-board estimate of just how much the flex changes due to cutting, because that's individual to each shaft and the shaft's original design:. To do that, the DIY golfer will have to:. Of course, you don't have to trim the shaft to shorten a club for the sake of accuracy—you could just order new shafts in the desired length.

If you are not able or willing to install new shafts yourself, check with local pro shops to find a club fitter. Actively scan device characteristics for identification.

Use precise geolocation data. Select personalised content. You can use something like a dremel, but getting the cut clean is not always that easy.

I've used masking tape and a Dremel. LoPan12 Member. Joined Aug 7, Messages Reaction score 0 Handicap With a normal cutting disc? Or one of the reinforced, or diamond coated ones? Bstubbs42 Member. Cuts metal and graphite shafts like butter. Taped around the shaft where I wanted to cut. Cut almost half way thru, flipped it and cut from the other side. Took less than a minute. If you don't plan to do a lot of cutting, it's a cost effective method. Tape the shaft area to be cut and use a hacksaw.

Sometimes use a Dremel, but, as previously stated, getting a straight, clean cut can be a challenge. Jman Golf Writer Guy. I use a Dremel for steel and graphite, easy peasy.

But, I've got a loooooooooot of practice. Have both dremel and chop saw. The saw is much easier. Mango Smash New member. JB said:. I use die grinder with a 3" cut off wheel. Works great for cutting and de-burring steel or cutting graphite. A good quality wheel can cut through a padlock in less than two seconds so golf shafts are child's play.

Hawk Master Painter. I like my chop saw quite a bit for butt trims, but it's dicey on tipping. Rory McIlroy is 6'1", but he uses a Note that When it comes to length , you should use the longest that you can control. The reason players tip shafts is to make them slightly stiffer than they were designed. Tipping instead of trying a different flex allows a player to find a shaft with a firmness in between flexes.

The average tip on drivers is about an inch, although some players go to greater lengths. Choking down on your driver is also a good method when you need to play a tee shot into the wind. The speed of your swing will be reduced when you choke down , which means your spin rate should be reduced as well. The tip stiffness or lack of may help the golfer. A softer tip shaft may allow the shaft to bend more into a closed position at impact, reducing a slice.

If you like the shaft you're playing but want a stiffer feeling, tipping it should deliver the desired result. Tipping a shaft , just like choosing a stiffer flex , does not guarantee lower spin. For all you physics minded golfers : If you hit a golfball with a heavy object, it goes far.

All things being equal i. The ball often flies off to the left and too high. The club's shaft feels very weak. You're constantly hitting the ball with the toe of the golf club. All clubs -- from putter to driver -- should sole flat on the ground when you address the ball main photo.

But if your clubs are too upright, the toe would be off the ground , and you'd have a tendency to pull the ball inset, top. Too flat , and the heel would be up, and you'd tend to hit pushes inset, bottom. Playing with clubs that are too long or too short can hurt your game. The right length of the golf clubs can make all the difference in a golfer's game.

Each club's length can greatly influence how far a golfer hits the ball and how straight they can hit. Can you cut graphite golf shafts?